Published July 9, 2026 at 06:05
In the calibration lab at Denmark’s leading metrology service provider, two sets of gauge blocks sit side by side. The classic Schut M112 grade 0 steel set for daily working verification. And the newer zirconia ceramic M32 grade 1 set, used when temperatures fluctuate or when critical traceability needs to be established. The calibration lab owns both because they have complementary strengths. Here’s why ceramic doesn’t simply replace steel — it supplements it.
Zirconia ceramic as a material
Zirconia (ZrO₂, zirconium dioxide) is a technical ceramic that has found applications in medical implant technology, fuel cells and — the main point here — in precision metrology. The material is not ordinary ceramic like porcelain. It is specially stabilized zirconia (Y-TZP, yttria-stabilized tetragonal polycrystalline zirconia), which produces a densely packed crystal structure with an unusual combination of hardness and toughness.
The practical consequences of the material:
Thermal expansion 9.2 vs. 11.5 × 10⁻⁶ /°C
Steel has a thermal expansion coefficient of ~11.5 × 10⁻⁶ /°C. Zirconia has ~9.2 × 10⁻⁶ /°C — 20% lower. The practical significance: on a 100 mm gauge block at a 5°C deviation from the 20°C reference:
- Steel: 100 × 11.5 × 10⁻⁶ × 5 = 5.75 µm expansion.
- Ceramic: 100 × 9.2 × 10⁻⁶ × 5 = 4.60 µm expansion.
The difference is 1.15 µm. Not much in absolute terms. But in a calibration lab with a climate-controlled environment at 20 ±0.5°C, the steel block’s expansion is 0.58 µm, the ceramic block’s is 0.46 µm. At a grade 1 tolerance of ±0.3 µm (25 mm block), 0.58 µm is already a significant share of the tolerance. 0.46 µm is marginally better — but in that world of precision, marginal improvements are valuable.
Even more important: ceramic is also thermally less reactive. Handling with bare hands heats steel more than ceramic, because ceramic has lower thermal conductivity. Practical consequence: after handling, a steel block must stabilize for 15-30 minutes, a ceramic block for 5-10 minutes.
Hardness 88-90 HRC vs. 63-65 HRC
Steel gauge blocks are hardened to 63-65 HRC (Rockwell C). Zirconia ceramic has a hardness of 88-90 HRC — roughly 40% higher. Practical consequences:
- Wear resistance: Ceramic surfaces wear down significantly more slowly than steel. With daily wringing and unwringing in a lab environment, ceramic lasts 3-5 times longer.
- Scratch resistance: Soft dust particles (paper dust, skin flakes) can scratch steel over time. Ceramic is practically immune to these.
- Surface integrity: The ceramic surface retains its microscopic fine-edge geometry longer, which is critical for the wringing process to function properly.
Corrosion resistance — practically total
Steel blocks must be oil-protected for storage — otherwise they develop rust that permanently damages the surface. The calibration lab therefore has routines for oil protection and de-oxidation before measurement.
Ceramic does not react with atmospheric oxygen, with condensation, or with acidic atmospheres. The block can be stored under ordinary workshop conditions without special climate control. No oil protection needed. No routine for removing oxidation before measurement.
Brittleness — the critical trade-off
Ceramic’s drawback: it is more brittle than steel. If dropped on the floor, zirconia blocks can fragment (a steel block might deform locally but not shatter). Practical consequences:
- Handling must be more careful — never rushed or subject to local bumping.
- Storage in a wooden case with form-cut padding is mandatory (not merely recommended).
- Transport requires a shock-absorbing outer case.
- The wringing process must be clean and smooth — no slipping.
Calibration labs using ceramic blocks have built extra procedures into their SOPs to reduce the risk of dropping.
Where the difference makes a practical difference
Calibration labs with thermally demanding environments: Even physical sub-micrometer differences add up in significance over the day’s temperature variations.
Critical traceability chain: When establishing secondary references for precision production (aerospace, medical implants), ceramic’s stability can be decisive.
High-frequency-use labs: Where the blocks are used daily for many calibrations, the wear resistance is economically advantageous.
Humid/corrosive environments: Workshops by the coast, marinas, or in the chemical industry, where steel blocks would otherwise require intensive rust prevention.
Cleanroom production: Semiconductors, pharmaceuticals, where no particle contamination is tolerated. Ceramic does not shed oxide flakes over time.
M32 vs M112 — what the difference means
The M32 set contains 32 blocks (the same interval structure as the M112 but fewer step sizes). The M112 has 112 blocks and can build up almost any dimension. The M32 covers the most commonly used dimensions but requires extra stack length for certain special values.
Practical logic: the M32 ceramic set is typically used as the calibration lab’s secondary reference. The M112 steel set for daily working verification. The combination provides high-use steel and precision ceramic with their respective strengths.
What you get for the money
Schut zirconia ceramic gauge blocks in set M32, grade 1 (ISO 3650/1), 32 blocks in standardized dimensions, hardness 88-90 HRC, expansion coefficient (9.2 ± 1) × 10⁻⁶ /°C, cross-section 30.9 × 9 mm (0.5-10 mm blocks) and 35.9 × 10 mm (10-100 mm blocks), supplied in a wooden case with the manufacturer’s measurement protocol, compatible with ISO 17025 calibration certificates. 9,517 DKK.
Compared to steel M32 grade 0 (~4,000-5,000 DKK), the extra cost is twice as high — but for calibration labs in climate-controlled environments, with high usage, or in corrosive environments, the investment is amortized through the instrument’s 3-5 times longer lifespan as well as reduced maintenance time.
Read more: Schut zirconia ceramic gauge blocks M32 grade 1 in the shop →