Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a secondVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a second

The surface doesn’t always tell you what’s happening inside: two temperature measurements in one handle

Published 15 November 2026 at 01:44

A pallet of chilled goods is standing on the loading ramp, and the surface feels cold. Even so, the core may be several degrees too warm, and you only find out when you insert a probe. Conversely, nobody wants to push a probe into a pipe run, an electrical cabinet or sealed packaging. In many places you therefore end up with two instruments in your pocket, and it is always the one you are missing that you need.

ETI Thermapen® IR, equipped with fold-away probe and non-contact IR temperature measurement, calibration certificate, red

What is the Thermapen IR

The ETI Thermapen IR combines an infrared thermometer and a penetration thermometer in a single unit. The foldable probe is used to measure the temperature inside a product, while the infrared sensor measures surface temperature without contact. The thermometer has a distance-to-spot ratio of 5:1, and the emissivity is set to 0.95 by default but can be adjusted between 0.1 and 1.0. With the mode button you can view maximum and minimum values for the infrared readings. A calibration certificate is included.

What problems does it solve

It removes the guesswork between surface and core. You can first scan a product or a surface quickly and then confirm with the probe where necessary. You also avoid having to clean and disinfect a probe between every single check when the surface temperature is enough for an initial assessment.

You do need to know the limitations, though. The 5:1 ratio means the measurement spot is roughly one fifth of the distance, so you must hold the instrument close to the target. Shiny metal surfaces have low emissivity and can give readings that are too low, unless you adjust the value or measure on a matt surface.

Three situations from practice

Food production and catering. At goods receiving, you check the surface temperature of crates and packaging in a few seconds. If an item shows deviations, you insert the probe and measure the core temperature as documentation. In the kitchen, the same probe is used to check the core temperature of cooked food.

Maintenance. A bearing housing, a motor or a panel that is running hot can be checked from a distance during operation. You quickly see whether a component deviates from its neighbouring units, and the max display captures the highest value during a walk-round.

Sanitary installations and ventilation. The surface temperature of pipes and risers shows whether circulation is working or whether a hot water line is getting through. If you need to confirm the water temperature at a tap, you use the probe instead.

Why it pays off

The economics lie in time and fewer sources of error. One instrument instead of two means that it is with you when it is needed, and that the check does not get postponed. Fast screening saves minutes per inspection round, and probe measurement is used only where it adds value. The calibration certificate is included, which makes self-checks and audits easier. A single avoided rejected delivery, or a stoppage detected before a component fails, can cover a large part of the investment.

See specifications and details for the Thermapen IR at mikrometer.dk if you want both surface and core in the same measurement.

Read more

More news

All news