Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The temperature was fine at the inspection, but what happened overnight?Air Temperature Is Not Product Temperature: How to Monitor a Refrigerator So the Reading Can Be TrustedSee the fault inside the pipe before you tear up the floor: 30-meter camera probe for pipes and hidden cavitiesThe Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The temperature was fine at the inspection, but what happened overnight?Air Temperature Is Not Product Temperature: How to Monitor a Refrigerator So the Reading Can Be TrustedSee the fault inside the pipe before you tear up the floor: 30-meter camera probe for pipes and hidden cavitiesThe Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One Instrument

The Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One Instrument

Published 13 November 2026 at 09:32

You know the situation: a bearing housing is running hot, a switchboard smells faintly of overheated insulation, or a delivery from the cold room needs to be checked before it moves on. You have an infrared thermometer in your pocket, but it only shows the surface. And when you need to know the temperature inside the product or in the liquid, you have to use a different instrument.

ETI RayTemp® 8, infrared thermometer for temperatures from -60 to +500 °C. 12:1 distance-to-spot ratio. With socket for type K thermocouple probe

What the RayTemp 8 is

The ETI RayTemp 8 is a compact, pistol-shaped infrared thermometer with a measuring range from -60 to 500 °C and a distance-to-spot ratio of 12:1. This means that at a distance of 120 cm, the measurement spot has a diameter of approximately 10 cm. An eight-point laser indicator shows how large an area you are actually measuring.

The instrument also has a built-in socket for type K thermocouples. With a suitable probe, you can measure from -64 to 1370 °C, allowing you to measure air, liquids and core temperature instead of just the surface. Probes are not included, but a set with a penetration probe is available.

What problems it solves

Non-contact measurement is fast and safe when the object is hot, rotating or hard to reach. The limitation is that an IR thermometer only reads the surface, and that shiny metal surfaces often give a reading that is too low. With the probe as a reference, you can check whether the IR reading can be trusted. You can also display maximum, minimum, difference and average, so you don’t have to note down values along the way.

Three practical situations

Maintenance and electronics: Scan a row of fuses, terminal blocks or motor bearings and find the one that deviates. The difference function shows directly how much hotter one point is than its neighbour, and that is often enough to plan a replacement before something breaks down.

Food production: Measure incoming goods on the surface of the packaging from arm’s length, and use the probe socket for the core temperature of the product that needs to be documented. One instrument, two measuring methods.

Installation and service: On heating pipes, underfloor heating and ventilation, you can scan pipework and outlet temperatures without contact, and then measure air or water temperature with a probe when the figure needs to go into a service note.

Why it pays off

The biggest saving is not the price of the instrument, which is around DKK 1,000, but time. When you don’t have to fetch an extra thermometer, and a quick scan can pinpoint the spot that needs closer examination, troubleshooting becomes shorter. A verified IR result with a probe as a backstop also leaves fewer doubtful cases when readings deviate, which saves repeated measurements and unnecessary rejection of goods. Automatic shut-off after 60 seconds keeps battery consumption down, so the instrument is ready when you need it.

Take a closer look at the instrument

If you currently have both an IR thermometer and a contact thermometer lying around, it is worth considering whether one instrument can cover both tasks. See specifications and accessories on the product page.

Read more

More news

All news