Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Air Temperature Is Not Product Temperature: How to Monitor a Refrigerator So the Reading Can Be TrustedSee the fault inside the pipe before you tear up the floor: 30-meter camera probe for pipes and hidden cavitiesThe Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Air Temperature Is Not Product Temperature: How to Monitor a Refrigerator So the Reading Can Be TrustedSee the fault inside the pipe before you tear up the floor: 30-meter camera probe for pipes and hidden cavitiesThe Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference Furnace

Schut thickness gauge 0-10 mm, type B: Micrometer, caliper, or special thickness gauge — which one wins when the leather is 3 mm and measuring force decides the result

Published July 8, 2026 at 17:56

There are three ways to measure the thickness of a piece of soft leather 3 mm thick in the Danish workshop today. A standard micrometer, a digital caliper, or a dedicated thickness gauge with a type B anvil such as the Schut 853.022. They will give three different answers. Only one of them is true.

Standard micrometer: 2.4 mm (compresses the material)

An ordinary 0-25 mm micrometer has a hardened steel spindle and anvil, both with Ø6.5 mm flat faces. The measuring force comes from the ratchet: 5-10 N under normal handling. On hard steel this is unproblematic — steel doesn’t compress. On leather or rubber it’s catastrophic.

The physics: the contact area between the Ø6.5 mm anvil and the leather is ~33 mm². With 10 N of force, that gives a pressure of 0.3 MPa (~3 bar). Leather compresses under that pressure by 15-25% — so a true thickness of 3.0 mm is measured as 2.4 mm. The measurement is 20% too low. Quality control decides the leather is too thin, the whole batch is rejected, and the error lies in the micrometer, not in the material.

Caliper: 2.8-3.2 mm (depends on the operator)

A digital caliper with flat jaws gives a better result because the contact pressure is lower — the caliper doesn’t have a ratchet mechanism that guarantees consistent force. The operator presses with whatever habit he has.

The problem: operator variation becomes enormous. The same man measures the same piece of leather three times and gets 2.8, 3.0, and 3.2 mm. None of them is necessarily “the true value,” because the force applied isn’t standardized. For QC work this is a death blow — the data isn’t reproducible.

Worse: the caliper jaws have a Ø1-2 mm contact surface in practice (the edge of the jaw cuts into the material). The contact pressure is locally high even at low force, and the material compresses at the contact point.

Type B thickness gauge: 3.0 mm (the true value)

The Schut 853.022 with a type B anvil has Ø10 mm flat measuring faces — 2.4 times larger contact area than a micrometer, 8-25 times larger than a caliper. With the same force, the pressure becomes:

  • Type B (Ø10): 10 N / 79 mm² = 0.13 MPa (1.3 bar). Leather compresses ~3%. Measurement error: 0.1 mm on 3 mm leather.
  • Micrometer (Ø6.5): 10 N / 33 mm² = 0.30 MPa (3 bar). Leather compresses ~15-20%. Measurement error: 0.45-0.60 mm.
  • Caliper jaw (Ø2 effective): 10 N / 3 mm² = 3 MPa. Leather compresses at the point. Measurement error: unpredictable.

The type B instrument also has an upper-jaw mechanism that is weight-loaded (typically 300-500 g, not spring-loaded), which makes the measuring force consistent regardless of the operator. The operator doesn’t “set” the measuring force — the mechanism does.

Schut thickness gauge 0-10 mm type B with Ø10 mm anvil faces for leather, rubber and soft wood

How deep is the throat depth — why 15 mm is often enough

The throat depth of 15 mm determines how far into the workpiece you can measure. Leather sheets, rubber seals, cork sheets and cardboard sheets are typically 100-500 mm wide. A 15 mm throat depth gives access 15 mm in from the edge — twice as far as an ordinary micrometer (~7 mm).

For all standard thickness measurements on sheets or strips, 15 mm is plenty. For measurements in the center of the material (e.g. in the middle of a 300 mm piece of leather), a special model with a longer throat is required, which Schut supplies on request.

Where it makes a real difference

  • The leather industry (shoes, bags, furniture, cars): thickness tolerance for quality leather is 0.1-0.3 mm. A standard micrometer is not approved.
  • Paper and cardboard production: the ISO 534 standard requires a dedicated thickness gauge, not a caliper or micrometer.
  • Rubber seals and gaskets: NBR, EPDM, silicone. A Shore A hardness of 40-70 makes the materials highly compressible.
  • Foam production (furniture upholstery, insulation): foam is 90% compressible — a standard micrometer is useless, only type B will do.
  • Soft wood and veneer: beech, pine, birch. Type B with a wide anvil doesn’t compress the fibers.
  • Textile and felt: mattress production, insulation. Type B with low contact pressure.

At 542 DKK, the instrument is the cheapest of the three solutions (micrometer 700-1200 DKK, digital caliper 500-2500 DKK), while at the same time being the only one that gives reproducible data on soft materials. It’s not a luxury — it’s the correct method.

Read more: Schut thickness gauge 0-10 mm type B in the shop →

More news

All news