Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a secondWhen the spirit level says flat, but the machine still runs crooked: angle measurement with 0.05° resolutionWhen two operators measure the same hole and get two different numbers: how three measuring points remove the uncertaintyVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a secondWhen the spirit level says flat, but the machine still runs crooked: angle measurement with 0.05° resolutionWhen two operators measure the same hole and get two different numbers: how three measuring points remove the uncertainty

Ceramic blocks don’t slide up, but they don’t grow with the workpiece either

Published 25 August 2026 at 05:50

A set of gauge blocks doesn’t wear out from measuring. It wears out from being used — from hundreds of wringings, where two surfaces are pressed together under pressure, and from the fingerprints that inevitably end up on a surface that has just been handled. Both attack steel. Neither attacks ceramic much.

Select ceramic gauge blocks in set M32, grade 0 to ISO 3650

What it is

A set of ceramic gauge blocks, M32, grade 0, to ISO 3650.

  • Hardness approx. 1350 HV
  • Coefficient of expansion α = 9.3 · 10⁻⁶ per kelvin
  • Sizes include 1.1-1.9 mm in steps of 0.1 mm, 1-9 mm in steps of 1 mm, 10-30 mm in steps of 10 mm, and 50 mm
  • Cross-section 30 x 9 mm up to 10 mm, 35 x 9 mm above
  • Supplied in a wooden case with the manufacturer’s traceable measurement protocol

What ceramic solves

Hardness is half the explanation. At around 1350 HV, this is significantly harder than hardened steel of gauge block quality, meaning the measuring faces resist the scratches and wear caused by exactly the kind of handling a workshop set is subjected to. A set used every week ages through its faces — if they become rough, the wringing gets worse, and once the wringing gets worse, the stack no longer holds together as a single piece.

Corrosion is the other half, and in practice the more important one. Steel rusts from a single fingerprint, because sweat is salt and water. That’s why steel blocks need to be wiped down, oiled and stored with care, and a set that was put away just once without wiping can be marked forever. Ceramic doesn’t corrode. A fingerprint on a ceramic block is something you wipe off, not something you discover too late.

And the catch worth knowing

The coefficient of expansion of 9.3 · 10⁻⁶ is lower than that of steel. At first glance that sounds like a pure advantage — and for stability, it is. But a gauge block is almost always used to check something made of steel, and the two materials then respond differently to temperature.

At the reference temperature of 20 degrees, everything is as it should be. But if you measure in a workshop that is a few degrees warmer, the workpiece grows slightly more than the block stack does, and the difference is real: over a hundred millimetres and a five-degree deviation, we’re talking about a good one micrometre from the material difference alone. For workshop tolerances, that means nothing. For work close to grade 0’s own limits, it needs to be accounted for — or the items need to be allowed to equalise to the same temperature before measuring.

Ceramic is also hard in a brittle way. It doesn’t deform the way steel does; it chips. A drop onto a concrete floor is therefore worse for a ceramic block than for a steel block, even though everyday use is gentler on it. It’s a trade-off: better against wear, worse against accidents.

Three typical applications

  • Calibration work: setting and checking micrometers and dial indicators, where the set is used daily.
  • Measuring room: reference dimensions for comparative measurement, where the condition of the surfaces is critical.
  • Workshop use with many hands: where the blocks aren’t always handled as gently as the instructions say.

Why it pays off

A set of gauge blocks is an investment expected to last decades, so the price difference between steel and ceramic shouldn’t be compared to the purchase price, but to the service life. A steel set used every day and handled by several people is, in the long run, a consumable; a ceramic set under the same use is far less so.

Then there’s what you don’t notice: a block with an early rust spot or a rough surface still measures something, and it won’t tell you it’s wrong. The material that doesn’t rust removes that entire source of error — not by making the measurement better, but by removing a way it can get worse without anyone noticing.

Read more about Select ceramic gauge blocks M32 →

More news

All news