Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a secondVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a second

When two operators measure the same hole and get two different numbers: how three measuring points remove the uncertainty

Published 16 October 2026 at 07:37

Most people know it from the workshop: a bore is measured by two people, and they get two different results. Not because anyone is careless, but because an ordinary internal measuring instrument with two contact points easily sits slightly crooked or fails to hit the true diameter. The difference is often a few hundredths of a millimeter, and those are exactly the hundredths the tolerance leaves room to argue about.

Analog internal three-point micrometer of the Holtest type for blind holes. Measuring range Ø62–75 mm. Scale division 0.005 mm. Self-centering. Carbide measuring faces. Replaceable measuring pins for larger sizes. Supplied in an aluminum case with extension.

What is a three-point internal micrometer?

It is a handheld instrument for measuring bore diameters, with three measuring faces spaced 120 degrees apart around the axis. When you turn the thimble, the three points spread outward until they rest against the bore wall. Because three points always define a circle, the instrument centers itself in the bore. This model covers Ø62–75 mm, has a scale division of 0.005 mm and carbide measuring faces. For larger diameters the measuring pins can be replaced, and it is supplied in an aluminum case with an extension.

What problems does it solve?

The main point is that the operator’s handling matters far less. The instrument cannot sit crooked in the same way as a two-point gauge, and you don’t have to “feel around” for the largest diameter. The model is also designed for blind holes, where you cannot get access from the other side. Before measuring, the instrument is set to zero on a setting ring at nominal diameter, and the deviation is then read directly in the bore.

Where is it used?

Hydraulics and pneumatics: When checking cylinder bores and valve bodies, a few hundredths of a millimeter decide whether a seal works. Here, repeatability matters more than speed.

Engine and compressor repair: When reworking cylinders, wear and any ovality must be documented before deciding between honing and replacement.

Machining and incoming inspection: When housings and flanges arrive from subcontractors, bores can be spot-checked at the bench without the part having to go to a measuring machine.

Why it pays off

The instrument costs around DKK 3,000. That is not cheap for an analog tool, but the math is simple. One scrapped housing, one unnecessary complaint or one round of rework caused by a wrong measurement quickly costs more. Add to that the time spent re-measuring and settling who is right. An instrument that gives the same result no matter who holds it removes those discussions. The analog design also requires no batteries or charging, and the carbide faces last a long time in daily use.

Remember to check the zero point against the setting ring at regular intervals, and to keep the instrument and the workpiece at the same temperature so that the measurement is not affected by thermal expansion.

See the instrument

If you work with bores in the Ø62–75 mm range and need measurements you can stand behind, you can see data and accessories on the product page.

Read more

More news

All news