Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a secondVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a second

The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits It

Published 19 November 2026 at 14:45

Most people who work at a machine know the situation: the caliper lies next to the spindle, gets a splash of coolant, and a few days later the display shows either nothing or a zero point that has shifted. Then you either measure by feel or go for a new instrument. Both cost time and create uncertainty in your measurements.

Tesa TWIN-CAL digital absolut skydelære, 0-150 mm med IP67-beskyttelse

What is the TESA TWIN-CAL

The TWIN-CAL is a digital caliper with a measuring range of 0-150 mm and a resolution of 0.01 mm. The jaws are made of hardened stainless steel, and the shaft length is 40 mm. The scale is matte chrome-plated, so the display does not glare under workshop lighting. It is built to ISO 13385-1, has a flat depth rod, and is supplied in a plastic case with a calibration report.

Two features set it apart from an ordinary digital caliper. The first is the absolute measuring system: the instrument always knows the position of the slider, so the zero point is not lost when it switches off automatically or when the battery (CR2032) is replaced. The second is the IP67 protection, which makes the electronics sealed against dust, coolant and temporary immersion.

What problems does it solve

With an incremental system you have to set zero at the jaws, and if you forget, you get a systematic error on every measurement. This is a classic source of error when operators change. Absolute measurement eliminates it. IP67 eliminates the other frequent cause of failure: moisture and oil getting into the electronics. If you want to clean the instrument, you can rinse it off instead of carefully wiping it down.

Where is it used

Machine shop: at the lathe and milling machine, diameters, lengths and shoulders are measured mid-process, while there is still coolant on the workpiece. Here the sealing is the decisive feature.

Incoming inspection: when components are received, many parts are measured one after another. With a data output, the values can be sent directly to an SPC system, so you avoid handwritten notes and typing errors.

Maintenance and assembly: when measuring wear on shafts, bushings and sealing surfaces, you switch between mm and inches at the press of a button. The locking screw holds the measurement, so you can read it off without having the instrument wedged between two surfaces.

Why it pays off

A caliper costing around two thousand kroner is not the cheapest on the shelf. The calculation, however, is about what a faulty measurement costs and how often a less robust instrument has to be replaced. Every part scrapped because of a shifted zero point, and every time an operator has to look for a working caliper, eats into the savings. A caliper that survives coolant and does not require resetting reduces both. On top of that, the calibration report and ISO 13385-1 make it easier to document the condition of the instrument in a quality system.

If your current calipers are often out of service or require zeroing before every measurement, the TWIN-CAL is a natural step. See specifications and accessories on the product page.

Read more

More news

All news