Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Three Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a secondWhen the spirit level says flat, but the machine still runs crooked: angle measurement with 0.05° resolutionVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Three Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a secondWhen the spirit level says flat, but the machine still runs crooked: angle measurement with 0.05° resolution

How much do your thermometers actually deviate? Find out with ±0.03 °C

Published 16 November 2026 at 09:37

The cold room shows 4 °C, and the handheld thermometer in the kitchen shows 4 °C. Yet the auditor stands there with their own instrument and reads 5.8 °C. Who is right? Without a known reference, neither of you can tell, and the discussion turns into a question of who has the most expensive thermometer. This is the situation a reference thermometer is made for.

ETI reference thermometer for calibrating other thermometers, incl. Pt100 probe and 5-point calibration certificate

What it is

The ETI reference thermometer is a master thermometer with a permanently connected Pt100 probe in class 1/10 DIN. The measuring range runs from -199.99 to 199.99 °C with a resolution of 0.01 °C. The system accuracy is ±0.03 °C between -49.99 and 149.99 °C and ±0.1 °C in the rest of the range. A 5-point UKAS calibration certificate is included, and the instrument is calibrated at the time of purchase. It weighs 210 grams, runs on three AAA batteries and has a housing with BioMaster protection, which is suitable for food environments.

What problem it solves

Thermometers drift. Probes get knocked, exposed to boiling water or put in the freezer over and over again, and the deviation creeps in without anyone noticing. A reference thermometer gives you a traceable value to hold your working thermometers up against. You don’t have to send every instrument to an external laboratory each time you are in doubt.

How to use it

The method is simple. The reference and the thermometer under test are placed side by side in a stable temperature medium, for example an ice bath at around 0 °C, a temperature-controlled water bath or a dry-block calibrator. Once both values have settled, you read off the difference and note it down. If the deviation is greater than your tolerance, the instrument is adjusted or discarded.

Three practical situations

Food production: Core and probe thermometers used to verify heat treatment and cooling must be documented in your own-check system. A fixed weekly comparison with the reference gives you a measured deviation that can be filed in your records.

Laboratory and cold or freezer rooms: Here the reference is used to check loggers and fixed probes in cold rooms, incubators and heating cabinets. A deviation of 0.03 °C is so small that it does not become a source of uncertainty itself.

Maintenance and installation: When testing heating and cooling systems, process water or control probes, the reference determines whether a suspicious value is caused by the system or by the probe.

Why it pays off

The calculation is straightforward. One reference can check many instruments, and each check takes a few minutes. You avoid external calibration of every single thermometer and the days when the equipment is away. More importantly, a hidden deviation of a couple of degrees can lead to rejected batches of goods or a non-conformity at audit. That is far more expensive than the instrument itself.

Delivery time is 10-14 days, because the product is calibrated before it is shipped. Plan the purchase well ahead of your next audit.

Read more

More news

All news