Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a secondVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleThe Surface Doesn’t Tell the Whole Story: Get Both Non-Contact and Contact Measurement in One InstrumentHow to Check Your K-Type Thermometer in a Few Minutes Without an Ice Bath or Reference FurnaceThe caliper read five hundredths of a millimetre too high for three weeks, and nobody noticedWhen it’s the tolerance, not the number, that counts: how to read serial parts in a second

Same bore, two different measurements: how to get an internal measurement that doesn’t depend on the operator

Published 13 October 2026 at 18:00

It has been seen many times: An operator measures a bore and gets 18.012 mm. A colleague measures the same bore and gets 18.004 mm. Neither of them has done anything obviously wrong, but the instrument sat slightly crooked in the hole, and now nobody trusts the number. The result is either a debate about who is right, or a part that is scrapped for no reason.

Analog internal three-point micrometer of the Holtest type. Measuring range Ø16–20 mm. Scale division 0.005 mm. Self-centering. Carbide measuring faces. Set supplied with setting rings and extension in a wooden case. Fast and accurate measurement of internal dimensions.

What it is

It is an analog internal three-point micrometer of the Holtest type for bores between Ø16 and Ø20 mm. The measuring head has three carbide measuring faces positioned 120° apart. When you turn the thimble, all three faces move out simultaneously and come to rest against the bore wall. The scale division is 0.005 mm, and the set comes with setting rings and an extension in a wooden case.

What problem does it solve

With three contact points, the instrument centers itself in the hole. You cannot hold it at an angle, and you don’t have to guess whether you have found the largest diameter. This removes the operator-dependent error that two-point instruments are prone to in small bores. A three-point principle can also detect a trilobed shape in the hole, which an ordinary two-point measurement does not see at all.

How and when it is used

First, you zero the instrument on a setting ring at the nominal diameter. Then you guide the measuring head into the hole, turn until all three faces make contact, and read off the diameter. This kind of measurement is called for when a bore needs to be approved and when a fit needs to be checked before the parts are assembled.

Three practical situations

Machined housings and bushings: In sample inspection in production, the micrometer quickly shows whether tool wear is pulling the diameter out of tolerance before a whole batch of rejects has been made.

Hydraulics and maintenance: When servicing small hydraulic cylinders and valve bores, you can measure wear directly and decide whether the component needs to be replaced or can be reused.

Incoming inspection and the measuring room: When delivered components need to be checked against the drawing, a self-centering instrument gives measurements that several people can repeat without disagreement about the method.

Why it pays for itself

The benefit lies not in the instrument itself, but in what is avoided. Fewer parts are scrapped or reworked because of uncertain measurements. Less time is spent on rechecking and on discussions between shifts. And you avoid having to choose between expensive limit gauges for each individual diameter and an instrument that cannot be trusted. For a workshop department that measures small bores every day, it is a modest sum compared with the cost of a single wrongly approved batch.

The setting rings in the set also make it easy to verify the instrument regularly, so you know it measures correctly before it is used on the next part.

Read more

More news

All news