Hoppa till innehåll
Gratis fragt over 3.000 kr. ekskl. moms! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the thermometer reads 3.0 °C but the product is at 5.5 °C: how to check your thermocouples at three pointsThe temperature was fine at the inspection, but what happened overnight?Air Temperature Is Not Product Temperature: How to Monitor a Refrigerator So the Reading Can Be TrustedSee the fault inside the pipe before you tear up the floor: 30-meter camera probe for pipes and hidden cavitiesThe Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handleVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the thermometer reads 3.0 °C but the product is at 5.5 °C: how to check your thermocouples at three pointsThe temperature was fine at the inspection, but what happened overnight?Air Temperature Is Not Product Temperature: How to Monitor a Refrigerator So the Reading Can Be TrustedSee the fault inside the pipe before you tear up the floor: 30-meter camera probe for pipes and hidden cavitiesThe Caliper That Doesn’t Lose Its Zero Point When Coolant Hits ItThree Seconds Instead of Twenty: How a Fast Probe Thermometer Changes Self-Monitoring in the KitchenWhen the caliper itself shows go or no-go, sampling inspection becomes faster and more consistentHow much do your thermometers actually deviate? Find out with ±0.03 °CThe temperature failed at three in the morning: How to spot it while there is still time to actThe surface doesn’t always tell you what’s happening inside: two temperature measurements in one handle

Rotary edge finder — a machine with thousandths-of-a-millimeter accuracy won’t help if the zero point is off by a tenth

Published August 20, 2026 at 22:14

A milling machine can position itself to within a few micrometres. The program is verified, the tool is measured, the workpiece is clamped. And yet the whole job still ends up offset, because the zero point was set by carefully jogging the spindle toward the edge and watching for when it “touched.” The machine’s accuracy doesn’t matter if the origin is wrong — every dimension in the program is calculated from that point, so an error introduced into the zero point will later show up in every single feature on the workpiece.

Rotating edge finder with Ø10 mm shank and Ø10 mm probe in steel and ceramic

What it is

A rotating edge finder with a Ø10 mm shank and Ø10 mm probe, where the measuring surface is made of steel and ceramic. Resolution and repeatability are both 0.005 mm, and it operates at 400–600 rpm.

What problem it solves

The edge finder relies on a small mechanical trick. The probe is spring-loaded and sits slightly off-centre, so when the spindle runs, the tip visibly wobbles. You then bring the workpiece — or the table — slowly toward the rotating tip. The moment the tip makes contact with the edge, friction starts pulling it in toward the centre, and the wobble decreases: the tip begins to run true. Continue just a little further, and the tip suddenly kicks sideways again — the characteristic “kick.”

That kick is precisely the measurement. At that moment, the spindle centreline is exactly one probe radius from the edge — with a Ø10 mm probe, that’s 5 mm. Zero the axis, move in 5 mm, and the origin is right at the edge.

The key point is that the method doesn’t rely on feel. “Did it just touch?” is a judgement call that varies between operators, between day and night shift, and with how well you can see down into the coolant. The kick is a binary, visible signal — either it has happened or it hasn’t — which is why repeatability can be held to 0.005 mm. The method is also gentle on the workpiece: contact occurs at low force, and the tip slides off instead of scoring a finished surface.

The ceramic measuring surface is part of what delivers that precision. Ceramic is hard and wear-resistant, so the probe’s diameter — which the entire calculation is based on — doesn’t change over time. It’s also non-magnetic and non-conductive, meaning magnetized workpieces and chips don’t pull on the tip.

Three typical applications

  • Setup on a milling machine: establishing the X and Y zero point against the workpiece’s edges, fast enough to redo for every new clamping instead of relying on a previous setup and hoping for the best.
  • Drilling to dimension: hole patterns that need to sit correctly relative to a reference edge — here, errors in the origin compound into every single position.
  • Clamping verification: a quick check that the workpiece is sitting where it should after fixturing, before any chips are cut.

Why it pays off

Consider the cost of a single offset workpiece. An incorrect zero point is rarely caught in the machine — it’s discovered during inspection or at assembly, by which point the workpiece already carries the value of every operation performed on it. And the error can almost never be repaired, because material has been removed in the wrong place. The edge finder costs less than most of the individual workpieces it’s used on.

Then there’s the time factor. Feeling your way toward an edge with a strip of paper or by eye takes longer than the seconds the kick requires, and the result is worse. A method that’s both faster and more reliable actually gets used every time — and that’s the difference that matters over the course of a year: not that the setup *can* be done precisely, but that it *is* done precisely, even on a busy Friday afternoon.

Read more about the Ø10 mm rotating edge finder →

More news

All news